The most common 3 faults suffered by Ricoh 1022

 

Do you own a Ricoh 1022 machine ? And you do not know how to deal with its faults or even diagnose it, Al-Ansar Printing Solutions will try to raise your efficiency in dealing with this model, in this article we will provide a detailed explanation of a number of common faults in this model, such as:  

1. Machine control screen malfunctions.
2. Crammed when printing large quantities.
3. Crammed into Trays 2, 3, and 4.

 During the following lines, we will talk about these breakdowns in detail and the reasons that lead to them, and how to deal with each cause separately.

• Machine control screen malfunctions

Machine  Ricoh 1022  features a screen touch screen controller ( Touch Screen ), which makes the user deals with the machine easily and quickly.

But sometimes the control screen is broken, and it does not respond to the orders that the user gives it to, or the customer complains about its slow response to the orders that are presented to it.

This occurs due to one of two reasons:

1. The first: the  presence of dust and ink exhausts on the control panel  (Mother Board) of the screen, which impedes its work correctly .
2. The second : some or all components of the control panel of the screen are damaged, which leads to the customer not responding to the orders.

The solutions proposed to eliminate this problem are:

• Clean the control screen rose well, and remove it from exhaust or dust .
• If part or all of the board is damaged, it is advised to change this part completely, so that you can handle the machine .

Second: The crowd when printing large quantities

Do you suffer from a crowd in the Ricoh 1022 machine  , and this crowd increases when printing a large number of copies? Here are the reasons for this:

• Drawing rollers

The accumulation of dust and exhaust on the pull rollers leads to a failure of the machine to pull the paper correctly, and there may be corrosion of it as a result of frequent use, which leads to the difficulty of pulling the paper or pulling it in a wrong way, which causes the jam .

• Heated nails

The nails of the heater may be damaged, broken, or clumped on the ink, which may cause it to not work properly.

• Paper Switch

The switch in copiers is a reader of paper sizes and weights, and based on its reading, the characteristics of the machine are adjusted to match the quality and sizes of paper .

 When the swatch misread it, a machine jam occurs, possibly due to dust or exhaust on it, or it may become damaged.

These problems can be solved as follows:

1. Clean the dust rollers from dirt, or change them if they wear .
2. Clean the nails of the heater if ink is accumulating on it, or change it if it is damaged .
3. Clean the swatch from dirt or change it if it is damaged.

Third: Crammed into Trays 2, 3, and 4

Did the paper path stop these drawers in the case of issuing an order to print or copy documents, there are more than one possibility that they cause a jam of drawers, as it is one of the most common malfunctions that affect Ricoh 1022 machine   as follows :

• Drawing rollers

There are two possibilities, the first: the accumulation of dust on it and the second: it may be corrosive as a result of frequent use and missed the roughness that enables it to withdraw the paper .

• Lift motors

Each motor tray is responsible for lifting the paper to a level that enables the rollers to move the paper from the tray to its normal course inside the machine .

Damage to this motor or poor performance can lead to this malfunction .

• Paper sensors

It is responsible for sending information to the machine stating that the paper is ready for printing, and therefore any error in this information causes an insect .

Sometimes dust builds up on it. This hinders their proper functioning, and sometimes these sensors get damaged .

• Paper swatches   Switch paper

It may be covered with dust and exhausts, which prevents it from reading the paper specifications correctly, which causes jam, and may be damaged or broken.

This possibility can be dealt with as follows:

• Clean or change drawing rollers if they wear .
• Changing the paper lift motor if it is damaged or slows down .
• Clean paper sensors thoroughly from dirt and exhaust, or change them if they are damaged .
• Clean or replace the swatch if it is damaged.

This way, dear reader, can deal with the most famous machine faults  Ricoh 1022 and  there are many other malfunctions, which we will talk about in other old_articles to come .. Follow us.